Sure-heat Cascade X2000 User Manual

USE AND CARE MANUALFOR OUTDOOR USE ONLYALWAYS KEEP YOUR GRILL COVERED WHEN NOT IN USEBEFORE YOU BEGIN – We’ve included easy-to-follow, step-by-step in

Assembly103c3a3a3c3bSTEP FOURa. Attaching (2) Self Tapping Screws through the pre-drilledholes on the Left Bracket for the Cart Door Pin into the Cart

STEP FIVEa. Use (2) self tapping screws to install the left drip pan guide inposition.Note: The end with flange facing inside of the grill.b. Repeat s

Assembly126a6b6c-6d6eSTEP SIXa. Loosen the four (4) grill mounting bolts so that there isapproximately 1/4” between the bolt head and grill bottom.b.

STEP SEVENa. Remove the screws from three handles.b. Use (2) screws removed in step 7a to attach the handle ontothe cart door.c. Repeat step 7b to ins

STEP EIGHTa. Place a piece of Styrofoam from the packaging inside the rolltop grill hood to leave the hood propped open slightly.b. Attach the left sh

STEP NINEa. Place a piece of Styrofoam from the packaging inside the rolltop grill hood to leave the hood propped open slightly.b. Attach the Right Sh

STEP TENa. Remove two screws from the burner valve assembly.b. Carefully insert the valve assembly into the cast burner. Youwill need to angle the tub

STEP ELEVENa. Place the electronic igniter button into the igniter hole on thefront left of the side burner shelf.b. Secure the igniter in place using

STEP TWELVEa. Center the brass burner cap on top of the sideburner head.b. Place the side burner grate on to the sideburner tray.Assembly1812a12b

Assembly19close-up of steps 13b - 13c13b13d13aSTEP THIRTEENa. Place right hand door on an angle over the right side doorpivot.b. Tilt the top of the d

2IMPORTANT SAFETY INFORMATION- Read this manual carefully before using your grill to reduce the risk of fire, burnhazard or other injury.- Extreme car

Assembly20STEP FOURTEENa. Slide the drawer assembled in step 7d - 7e into the drawerguides under the front face. Make sure the little wheels on thesid

STEP FIFTEENa. Insert the flavor grids into the cutouts with triangle ridgesfacing up.b. Install main cooking grates on the ledges provided on the gri

22L.P. GAS INSTALLATIONCascade™Gas Grills that are set to operate with L.P. gas come with a high capacity hose and regulator assembly.(Note: Only use

23GENERAL INFORMATIONAlthough all internal gas connections on the grill are leak tested prior to shipment, a complete gastightness check must be perfo

24BEFORE LIGHTINGImportant! Before Lighting:• Check the gas supply line for cuts, wearor abrasion.• Always keep your face and body as far awayfrom the

25GRILL LOCATIONDo not use the grill in garages, breezeways, sheds or any enclosed area. Never operate the grillin enclosed areas as this could lead t

The grill rotisserie system is designed to cook items from the back using infrared heat. The rotisserie burner is aninfrared type which provides inten

ROTISSERIE LIGHTINGOpen the lid. Push and turn the control knob for therotisserie counter clockwise to the “ HIGH” position.Wait 5 seconds. Then press

28GENERAL MAINTENANCE- Keep outdoorcooking gas appliance area clear and free from combustible materials, gasoline and other flammablevapors and liquid

29GENERAL TROUBLE SHOOTINGYou should inspect the burners at least once a year or immediately if any of the following conditions occur:• The smell of g

3Please retain this manual for future reference© 2007 Sure Heat Manufacturing All rights reservedCongratulations on your purchase of a new grill! We a

30PROBLEMGrill will not light with a match or low heat with dial setto "High" position.Flame is erraticFlare-upsBurner flame is mostly yello

Warranty31

4Do not use the rotisserie in the rain.Electrical Grounding InstructionsThis appliance (rotisserie motor) is equipped with athree-prong (grounding) pl

Grill Features51. Roll Top Grill Hood2. Rotisserie Kit3. Grilling/Cooking Surface4. Side Shelf5. Control Knob: Rear Infrared Burner6. Control Knobs: M

Getting Started6

Assembly71b1c1a1dSTEP ONEa. Use (2) Screws secure the Rubber DoorStop on the Cart Base.b. Set the Cart base on the floor and then lay theCaster Assemb

Assembly82a2c2d2b2f2eSTEP TWOa. Place the Cart Side Left onto the two (2) outer fixedcaster assembly bolts, make sure the large flangeis toward the fr

Assembly9The Spare L.P. Gas TankBarrier must be installed toprevent storage of spare L.P. Gas Tanks.Failure to comply with these instructionscould res